Frequency Set

Sets the transmission frequency.

Unlock frequency field.

Power Set

Sets the output power level in watts.

Unlock power field.

RF Mute on Silence

Selects the time after which the transmitter's output will be muted if the transmitter is transmitting silence.

Click 'Mute RF' to manually mute your transmitter.

Unlock mute rf button.

FSK

Sets interval between FSK messages.

Enter your FSK text into the box. This will be converted into morse code. Accepts text of up to 16 characters.

Power Schedule

Enables/disables Power Scheduling.

Power Set

Selects the output power that will be set during the scheduled interval

Start Time

Selects the time at which the output power will change from normal power to scheduled power.

Finish Time

Selects the time at which the output power will change from scheduled power to normal power.

MPX Source

Selects the source for the exciter. - Internal: selects internal generator. - External: selects MPX BNC input.

Audio Input

Selects the input source.

Pre-Emphasis

Controls the pre-emphasis. Options are Off, 50 uS (Europe) and 75 uS (USA).

Input Channels

Selects mono or stereo.

Processing Preset

Loads the audio processing preset.

Type

Configures the Alarm pin as an Alarm (Open Collector) or as an Analog Output (0 to 5 volts) to interface with Telemetry equipment.

Source

Selects the parameter that will be reported as an analog voltage in the alarm pin. VOut = 5/1.2*CurrentValue/NominalValue. Please refer to the manual for further information.

Source

Selects which detector is the source for the alarm.

Threshold

Selects the threshold at which the modulation level alarm will be activated. This parameter accepts values from 1000 to 100000.

Threshold

Sets the threshold at which the forward power alarm will be activated. This parameter accepts values from 0 to 2000.

Threshold

Sets the threshold at which the reverse power alarm is activated. This parameter accepts values from 0 to 2000.

Threshold

Sets the threshold at which the PA Temperature alarm will be activated. This parameter accepts values from 0 to 150

On Delay

Sets how long the error condition must occur for before an alarm is triggered. This parameter accepts values from 2 to 600.

Off Delay

Sets how long the error condition must have stopped for before an alarm is un-triggered. This parameter accepts values from 2 to 600.

Email

Selects if an e-mail will be sent when the alarm state changes.

Pin Polarity

Selects whether the output is active high or active low.

Enabled

Enables/disables the trigger.

Action

Determines the action performed upon trigger.

Email

Selects if an e-mail will be sent when the alarm state changes.

Message

Sets the message that will be sent when the Trigger changes to ON. Accepts text of up to 300 characters.

RS232

Enables/disables logging to RS232.

File

Enables/disables logging to file.

UDP

Enables/disables logging messages to a remote UDP logging/syslog server.

IP Address

Sets the IP address where the log messages should be sent via UDP. Accepts IPv4 address in the form www.xxx.yyy.zzz.

Port

Sets the port where the log messages should be sent via UDP. Disable UDP to change. This parameter accepts values from 1 to 10000.

Email

Sets the method used for sending emails. For simplicity, choose BW Broadcast.

From

Sets the email address of the sender. The unit will send e-mails through this address. Accepts text of up to 64 characters.

To

Sets the recipients of the emails. Multiple addresses must be separated by commas. Accepts text of up to 99 characters.

Host

Sets the IP address of the SMTP server. Accepts text of up to 64 characters.

Port

Sets the port number of the SMTP server. This parameter accepts values from 1 to 1024.

Username

Sets the username for SMTP authentication. Must be left blank if no authentication is required. Accepts text of up to 64 characters.

Password

Sets the password for SMTP authentication. Must be left blank if no authentication is required. Accepts text of up to 64 characters.

Max Daily Emails

Sets the maximum number of emails allowed to be sent by the unit in a single day to stop spamming from intermittent errors. This parameter accepts values from 1 to 1000.

Click 'Test e-mail' to trigger a test run of the e-mail settings above. If you do not receive the e-mail within a few minutes, check the settings are correct and try again.

RS232

Enables/disables the RS232 remote.

Baud

Sets the RS232 baud rate.

Telnet

Enables/disables the telnet server.

Port

Sets the telnet TCP port. Disable Telnet to change. This parameter accepts values from 1 to 1024.

Date

Sets the date of the Real Time Clock. Accepts date in format dd/mm/yy.

Time

Sets the time of the Real Time Clock. Accepts time in format hh:mm.

Location

The physical location of this device (e.g., `TX Site 1, Rack 2'). Accepts text of up to 64 characters.

Contact

The contact details for the person who manages this device. Accepts text of up to 64 characters.

Screen Saver

This allows the time-out before the screensaver starts to be adjusted between 15s and 30 minutes.

Front Panel Lock

Enables/disables the screen lock code.

Front Panel Lock Code

Sets the screen lock code.